If you decide to decorate the apartment wall painting on the plaster, we will tell you how to perform this work without the help of the artist, and achieve the desired result with less costs and much faster.
Photo: "Applico"
The technology of manufacturing classical frescoes is quite complex. First, a layer of plaster consisting of a mixture of river sand and chopped limestone is applied to the wall. Then a long period of drying, during which chemical reactions that give it exceptional strength are underway in the plastering layer. At this time, another wet surface is signed by manually with mineral paints. Mandatory final stage - natural dried by finished frescoes under the rays of the sun. It is not surprising that in the age of speeds and new technologies, fresco fresco-based on the domestic market became the most popular on the domestic market. They are represented by the company "Applico", «Orthograph," Affresco, Fresconovo.
Photo: Quelyd.
For frescoes on a flieslinic basis, adhesives for flier-linovy and heavy fliesline wallpaper are used, separating their slightly ground
In the production of flieslinic sheets are covered with a thin layer of elastic plaster (from 1-3 mm), which is reliably fixed on a nonwoven base. Then the print method is applied by printing. For some manufacturers ("Applico", Affresco), the process of creating the frescoes includes another step - a manual fragmentary painting. She performs a professional artist. Then the colorful surface is maintained by a special composition, and in completion is covered with varnishes or other protecting and strengthened compositions. Frescoes on the flieslinic basis are intended for rooms with a temperature regime from 8 to 35 ° C. The colorful image will remain unchanged over 10 years, if moisture will not come and accumulate on the wall, and without the impact of direct sunlight - more than 12 years. The price of frescoes on the flieslinic basis depends on the decorative effects and surface textures, the minimum for 1 m² - 3990 rubles.
Photo: "Applico"
Special adhesive for frescoes
The elastic plaster layer allows you to minimize the canvas of modern frescoes on a flieslinic basis into a roll, like wallpaper. Its transportation and installation also resemble work with wallpaper. However, it should be remembered that each linen of a large format frescoes has a small allowance (about 5 cm) on both sides. With the right installation, one of the canvases are raised on the other so that the drawing coincided. Only in this case the junction line will be invisible. Caring for frescoes on a flieslinic basis is completely simple. They easily carry the impact of a wet napkin, and in the case of severe contaminants, a soap solution and a soft brush are used to purify the surface.
Installation of the frescoes "Applico" on the plastered wall
Before installing the frescoes on the prepared (durable, smooth and dry), the base is applied to the acrylic soil of deep penetration. The product is unpacking, following the instructions on the package. If the fresco tube was at temperatures below -10 ° C, it is left in a warm room for 12 hours for acclimatization. Before performing work, it is important to make sure that the temperature in the room is above 10 ° C and there are no drafts. To properly fix the fresco, the walls are placed.
Remove the brackets, open a tube, remove damping pads, turn the tube and take a neatly removed roll
The frescoes are spread on the floor, measure and checked the parameters with the specified in the order.
Prepare a solution of dry adhesive mixture for heavy flieslinic wallpaper. The marked area is first ground with liquid glue and leave for 30 minutes.
It is then abundantly applied glue, diluted slightly conventional, layer 2-3 mm using a painting roller
The canvas are applied to the working surface (there should be no air bubbles under it) and rolled the rubber roller from the center to the edges, not stretching
Excess glue from the edge immediately clean the clean napkin
In completion, check the density of adjacent angles and edges to the base. If necessary, the brush is applied to the glue and tightly pressed to the surface. While glue and fresco dry (for 10 hours), the windows and doors indoors are kept closed.
The main stages of the production of frescoes on the flieslinic basis are performed by hand, among them the application of textured plaster on the canvas, Dorivovka, aging, varnishing, etc. The maximum size of the seamless cloth reaches 3.2 × 9 m. Fixed frescoes are made up of several canvases. Those who have experience gaining heavy fliesline canvas can perform work independently. But it should be borne in mind that the storage period of the frescoes, carved into the roll in the manufacturer's container with a closed lid, is not more than 6 months from the date of manufacture. The canvas, which was in such a form more than a month, unfold very neatly, do not pull for the corners, do not allow fuses. Freeing from the protective stretch film, as it turns it slightly moistened from the sprayer. After that, they leave for 10-15 minutes so that the fresco absorb moisture and become softer. The process is simple, and yet, for impeccable installation, we recommend contacting professionals.
Vadim Lebedev
Technical Director of Manufactory "Applico"