Reference to the free planning apartment with a total area of 80.5 m2 for young spouses.
1- concrete slab overlap;
2 - waterproofing;
3- screed;
4- cork coating;
5 - foil;
6- Heating mat;
7- screed;
8 glue;
9- Ceramic tile
1- concrete slab overlap;
2 - soil;
3- leveling mixture;
4- substrate from foamed polyethylene;
5-Parquet Boards connected by a tongue
Two rooms and nothing superfluous, just necessary, but but good quality. White sofa, green aquarium, dossia wood floor and a little cherry furniture. They dreamed of an octaca apartment, she turned out.
Redevelopment
One bedroom apartment for young spouses is quite natural: and not much, and not enough. It meant one of the many modern dwellings, which are conditionally accepted to call free plan apartments. Actually, the interjection of functional zones to the hosts is often proposed to provide for the construction of the building - the structure of the building allows you to leave the minimum number of internal bearing structures. I comply with some rules, I comply with some rules, you can share the space on the premises in accordance with the desires of the customer. Among other things, in such houses it is easy to rebuild the inner partitions if they have already been put as much as we wanted. True, then the hosts carry extra costs: to buy an apartment with established partitions (the apartment without partitions would cost cheaper), to dismantle these most partitions (with the export of construction garbage) and the construction of new ones.The heroes of our story did not go to the first and not on the second, but on the third path, saving the maximum of funds. How exactly? Yes, they just liked the original layout, and it was almost not changed. Redevelopment actions have minimized: laid the old entrance from the corridor into the kitchen and removed part of the non-carrying partition between the kitchen and the living room. AB The rest of the family budget went to finishing work, installation of equipment (plumbing, heating and air conditioning systems, kitchen apparatuses), loggia insulation and the purchase of furniture. For the implementation of all this, specialists of the repair and construction company Gale were invited.
Floors
When preparing the base under the parquet board, which was intended to lay a floating method, as well as under ceramic tiles, retained an existing screed. The reason was a good "diagnosis", delivered after climbing "to emptiness": It turned out that the screed was tightly held on the concrete overlap and does not crack. They removed it only in small areas - in the kitchen (9m2), in the bathroom (5m2) and in the toilet (1m2). Here, a new waterproofing (domestic bituminous mastic "bisks" was laid on the cleaning plate (domestic bitumen mastic "bisks") and there were electric heating mats Celhit (Spain) between the layers of the new screed.
The floors in the rest of the apartment found it necessary to align a little. To do this, used quite expensive Finnish composition "Old 3000" (Optiros, Finland), since it did not need it. Previously, the foundation was thoroughly cleaned with a vacuum cleaner and rebounded with a solution of the "Old Primem" solution. The primer ensured the setting of the leveling mixture with the concrete basis, prevented the formation of air bubbles and pulling water from the mixture to concrete. A quick ripening composition of "Old 3000", filling the cavocratic spatula, filled with a ripening spatula and creating a smooth horizontal plane. After 5 hours, this freshly washed surface could be walking. The Analy next day is a new screed in some places, creating an ideal surface for the flooring of the parquet board, which was planned to be mounted every other day. The repair was done in summer, the heating was already disabled, but the warm weather (+ 20c) contributed to the timely drying and ripening the prepared surface. We note that if the tie "treated" the usual sandy cement mixture was "treated", it would take no 3 days to ripen, as in our case, and as many as 28.
For floor decoration in the living room, bedroom, corridor and dressing room, the Dussie Lux three-layer parquet board was decided to use Teka (Germany). Juicy amber-red, close to cherry, the color of the Dossi wood really liked the hostess. In accordance with it, they tried to select not only plinths, but also wooden furniture, as well as floor ceramic tiles and doors with platbands. Especially spectacular and elevated on a white, creamy shade, sofa in the living room. A parquet board with a deck gluing plank was laid diagonally, which resulted in an additional visual increase in the living room space, it began to seem even more extended. The idle of a narrow corridor (95cm wide) such laying had to be very stapled by the strap oriented across its directions than and contribute to the visual expansion of the room. Ceramic tile also decided to lay exclusively diagonally in order to at least an illusory increase in small areas of zones and premises for which it was intended: toilet (1m2), a dressing room (3m2), a bathroom (5m2), hallway and kitchen zones (each- approximately 10m2).
Cost of dismantling and preparatory work
| Type of work | Area, m2 | Ral payment, $ | Cost, $ |
|---|---|---|---|
| Dismantling partition | four | 3.6 | 14,4. |
| Cleaning surfaces from pollutes of mortarNBSP; concrete mixtures and heins | fifty | 2,3. | 115. |
| Repair of the joints of overlapping and walls (with a fantastic and sealing solution) | 12 | 2.7 | 32.4 |
| Dismantling of the cement-sand tie | fifteen | 3.5 | 52.5 |
| Loading and removal of construction trash | - | - | 200. |
| Total | 414,3 |
Cost of work on the device of floors
| Type of work | Area, m2 | Ral payment, $ | Cost, $ |
|---|---|---|---|
| Device reinforced cement-sand tie | fifteen | 10 | 150. |
| Device of bulk floors | 65.6 | five | 328. |
| Waterproofing device | fifteen | 7. | 105. |
| Flooring device (parquet board) | 47.99 | 10.3. | 493,4 |
| Flooring of floors with ceramic tiles | 32.6 | 17,4. | 567.3. |
| Total | 1643.7 |
Cost of materials for flooring device
| Name | number | Price, $ | Cost, $ |
|---|---|---|---|
| Dry mix (cement-sand) | 750kg | 0.06. | 45. |
| Bulk floors "Old 3000" (Optiroc) | 450kg | 0,7 | 315. |
| Hydrokhotloizol, bitumen mastic | 30m2 | one | thirty |
| Parquet board, Plinth Teka (Germany) | 47.9M2. | 43. | 2060. |
| Ceramic tile (Spain) | 23.1m2 | 25. | 577.5 |
| Ceramic tile (Italy) | 17,4m2 | 38. | 661,2 |
| Tile glue "Yunis" (Russia) | 230kg | 0.4. | 92. |
| Total | 3780.7 |
Ceilings, Walls, Electrician
The ceilings in the whole apartment were, as usual, unevenly cast concrete slabs of overlaps, and the seams between them were "impressive". To reduce the time to create smooth ceilings and generally simplify the task, we decided to resort to the technology of the metal frame of the metal frame sheets of plasterboard. The height of the premises was reduced by 4cm. But the result was achieved with the highest possible ease and efficiency, quickly and efficiently, without the use of complex and expensive plastering works. Of course, the ceiling frames have strengthened the wires for eight-built dotted lamps between metal slats, and even for four square sconces (Domus, Germany). To reach them the wires from the ceiling, I had to make short shutters in the bearing walls. Achetoba to avoid deep sticking, decided not to lay the wires in thick corrugations, but use a thinner cable PVA. Thus, it was possible to do with minimal depths, only 1.5 cm, and the bearing walls were not weakened.In the same way, from the ceiling on the walls, we descended the wiring to the luminaires in the hallway and the bedroom (the cost of these Brass - from $ 115 to $ 192, the manufacturer, also DOMUS). Even the rosettes on the bearing walls were not installed, and they mounted on the plinths, under which the cable strengthened. Above the ceiling zone, the ceiling was still on 10 cm and an air duct pipe from the exhaust to the ventilation hole and wiring to four built-in point luminaires was mounted in the cavity. In addition, not to make unnecessary strokes in the walls, part of the ceiling wires are placed in the cavity of the kitchen equipment.
Spanish ceramic tile from Keraben for walls and floor in the bathroom and toilet (total cost- $ 1608,5). Moreover, used different format tiles: Slate Ivory (3333cm), Slate Ivory (25,533cm), Slate Listelo Manila (723.5cm), Slate Modula Manila (223.5cm), Slate Taco Manila (811cm) and Slate Ventana (23,533cm). Also, different format tiles applied to facing the floor and walls of the kitchen. This Italian material of Serenissima: 9M2 coatings Octagona Reale (42.5 42.5.4 cm) at a price of $ 38 / m2, only $ 328; Plus 4m2 QUARRY STONE SAND (1010CM) models for $ 44 / m2, only $ 176. Came added decorative inserts TOZZ MARBLE ROSSO (33cm) - 56 pcs. $ 3, total cost- $ 167.
Weighted and on the balcony there is a Cairo Guero Octogon tile from the Spanish firm Azulejos Borja-20m2 at $ 24.8 / m2, and only $ 496. Additional decoration, decorative ceramic border Estrella Martos Cuero- 95 pcs. $ 1, that is, $ 95. Thus, for the hallway and the balcony bought a tile for $ 5910.
Similarly, the ceilings and lighting and the rest of the apartment (in the hallway, corridor, a dressing room and a bathroom with a toilet) were arranged. That is, everywhere, except the bedroom. It was decided to create a more expressive design, which is a rectangular plate with a thickness of 12 cm, as if cut off from the main surface of the ceiling and "soaring" above the bed. The design itself is made by a hollow, in the form of a frame, covered with plasterboard, and hides in itself a luminescent illumination that illuminates the ceiling. Already reflected from the snow-white plane, the light gently spreads throughout the room, although the bright elements themselves are not visible and do not irritate the eyes.
Concrete walls in quality differed from the ceilings for the better, so that they could be brought to the desired view using a plaster mix "Rotband" and the putty "Old Kr". The hosts did not put the task before finishers to level the surfaces of the walls and ceilings to the exact intersection under 90. It would be too expensive, because it would require significant efforts of plasters and a solid payment of their highly qualified labor, as well as the acquisition of a large number of expensive plaster, which would be applied with thick layers ( places up to 5-7cm). It was sufficient to achieve strictly vertical surfaces in the place where the installation of kitchen furniture was planned (so that it is close, without curves of the gaps, fit to the walls), and also well align the lower parts of the walls along the floor line (so that it is later tightly and without cracking to strengthen the plinths). AB remaining zones considered only the importation of surfaces to aesthetically acceptable level (the admission of curvature is 5mm for 2 m). After all, the walls after the alignment were assumed not to paint, but to have matte wallpaper, under which there is no need to create a perfectly smooth and smooth surface, irregularities remain unnoticed.
Punching of the soil, providing a strong setting of wallpaper with plastered walls, used sooping primer DUFA (MEFFERT, Germany). It not only helped to easily and highlight wallpaper on the surface, but also created a durable film, which will subsequently alleviate the shift of the coating. Wallpaper can be removed without problems from the walls, they will not leave the hard-dyed paper layers and will not break down with pieces of plaster, as often happens if the ground is not used. For wall pasting, 35 wallpaper rolls were required (from Rasch) $ 19 each (total cost was $ 665). The masters were offered to use the high-quality wallpaper glue of the Euro 3000 SpeziaLKleister from Pufas (Germany). After the end of work in existing sockets, the mechanisms of sockets and switches with decorative frames were installed (all these are ivory, from the Spanish company Simon). The apartment as a whole was needed 54 outlets (electrical, TV, telephone, for the selected Internet line) and 30 switches. Total cost - $ 956.
Dussie Lux Parquet Board (TEKA) was purchased for a living room, a corridor, a bedroom and a dressing room. 25 packs were purchased at 2.574m2, that is, 64.35m2. Price - $ 40 / m2. Total cost - $ 2576. Glue for Bakit-NF Parquet Parquet Boxes (Kiesel, Germany) - 3 packs of 0.75 liters. Packaging price- $ 6.7. Plinth Burkle Dussia (TEKA) - 85 pog. m on $ 3 / m2. Waterproofing and sound-absorbing substrate for parquet boards - 65m2, price- $ 1.7 / m2, total cost - $ 110.5.
Thus, all materials for creating a wooden flooring in the apartment cost $ 3112.
The cost of installation of suspended ceilings
| Type of work | Area, m2 | Ral payment, $ | Cost, $ |
|---|---|---|---|
| Installation of suspended ceilings from GLC | 63.3 | 17. | 1076. |
| Installation of suspended ceilings from GLC (complicated) | fourteen | 22. | 308. |
| Total | 1384. |
Cost of materials for mounting partitions and suspended ceilings
| Name | number | Price, $ | Cost, $ |
|---|---|---|---|
| Sheet Gypsum Carton Gl | 70m2. | 1.9 | 133. |
| Profile, screw, tape Sealing, sound insulation stove | by 53,5m2 | 5,4. | 341.8. |
| Total | 474.8. |
Radiators
The aesthetic view of the hosts installed by the builders did not satisfy. They were also required to repaint them, so under all three windows mounted new heating radiators. At the same time, the sectional Italian aluminum products Callidor Super 500 from Fondital ($ 11 per section were calculated on the working pressure of 16 atm). Under the windows in the bedroom and in the kitchen zone, identical radiators collected from eight sections each ($ 11 8 2 = $ 176) were installed, and in the living room, one long radiator of twelve sections ($ 11 12 = $ 132). Thus, the combined space of the living room and kitchen (almost 35m2) is overaged by twenty heating sections (plus the floor heating system in the kitchen), and the 14m2 bedroom. When installing radiators, the installation parameters recommended by the manufacturer are: 12cm from the floor, 2-5 cm from the wall to the back of the radiator and 10 cm from the windowsill. For work, it took a set of parts (adapters, plugs, gaskets, screw brackets) for a total of $ 17, as well as 3 R66A 1/8 air valves "(Giacomini, Italy) for $ 1 each intended for manual air output. Separately acquired and elements of the shut-off reinforcement. Since the heating system in a single-tube house, together with thermostatic valves, jumpers were installed between the feed and inverse pipes - to adjust the heat transfer of only its radiators without affecting the entire riser of the house.Doors, windows, loggia
Decorating the apartment with wooden finishing of warm saturated tones and choosing, under the age of this, interior doors, the creators of the interior, naturally stopped on the models of the cherry tone (from the Italian company LEDIVA, cost- $ 565). The books were purchased accessories of the same manufacturer: Various glass inserts (three white mats $ 58, two corrugated fiore $ 42 and one patterned Torino for $ 109) and for all six interior doors of LAMB handle for $ 23. When ordering the entrance door was preferred by the domestic option from the company "Gardian" ($ 905).
The glazing of the loggia and the installation of new plastic windows (all of the German profile Rehau) was carried out by the Russian company Plastok. In total, along with the loggia, the apartment was installed 6 windows in the amount of $ 2246; 5 windowsides for $ 179; 9 Tops $ 245 and 3 Mosquito nets for $ 83. Delivery and installation work cost $ 551, and the entire order, taking into account the discount of $ 496, cost young spouses at $ 2808. The computers are not included in the installation of windows, only alignment and the color of the slopes, they assumed plasterers.
The loggia, the parapet of which was originally completed with a thickness of one brick, decided to insulate. To do this, first filled with the mounting foam small gaps between the walls and the glazing frames, and then on both sides carefully plastered. Then the walls and the ceiling were stuck with a rolled material "Hydrokhotloizol", and on top, on a dowel, attached a wooden lattice frame, treated in two layers of the Aquatex composition. Skupport (4545cm) The skeleton cells were laid by the insulation of Isover ("Flyderer-Chudovo", Russia) with a thickness of 5 cm. He was "shot" with a three-millimeter layer of rolled polyethylene and the same, which was used as a substrate under a parquet board. In the case, he plays the role of vaporizolation of the insulation, as well as an additional insulation layer. The ceiling and wall-mounted "pie" finishes moisture-resistant drywall - two layers. Witting The warming design on the walls and the ceiling has a thickness of approximately 76mm.
The floor on the loggia was insulated otherwise. Initially, it was located significantly lower than the level of floors in the apartment, so, insulating, it was raised almost 8cm. The result was smoothed down the step when entering the loggia. Then, a concrete plate was glued to peeled from dust (with the help of a gas burner), all the same "hydrohoteloisol", connecting it to the vehicle with that waterproofing, which was previously fired on the walls of the fence. From above laid plates of the insulation Floormate 200 (Dow Chemical, United Kingdom) - extruded polystyrene foam 50mm thick. This material is capable of withstanding significant mechanical loads without deformation. It was closed with a steam-insulating polyethylene film and, rolling over the surface of a metal reinforcing road grid, filled with cement-sand tie 20mm thick. After its ripening, the floor, as in other rooms, was finally leveled with a thin layer of the composition "Old Time 3000", for which the day after two was glued with ceramic tiles.
In the process of making a screed in the hallway, a bathroom and in the kitchen mounted a warm floor system. These territories, like a toilet, subsequently told ceramic tiles. To create a system, heating mats from Celhit (Spain) were used - shielded cable, fortified on the grid.
For the hallway (9m2) of the components bought for $ 175, for the bathroom (5m2) - by $ 87, for the kitchen (9m2) - $ 109. Three built-in FRE 525 22 temperature regulators were worth $ 71, three tripods to them $ 10. It also took 27 sheets of cork substrate under mats - $ 2.7 (total $ 73) and 14m2 foil for $ 3 to $ 42.
The cost of finishing work
| Type of work | Area, m2 | Ral payment, $ | Cost, $ |
|---|---|---|---|
| Watching surfaces | 112. | 10 | 1120. |
| High-quality staining of surfaces | 68.3 | 13 | 887.9 |
| Wall pastry wallpaper | 112. | five | 560. |
| Facing the walls of GLC | 74. | eight | 592. |
| Facing walls with ceramic tiles | 33,4. | 21.8. | 728,1 |
| Installation of door blocks | 4 things. | 55. | 220. |
| Total | 4108. |
The cost of materials for the production of finishing works
| Name | number | Price, $ | Cost, $ |
|---|---|---|---|
| Gypsum Plaster "Rotband" (Russia) | 36 bags | 8.9 | 320.4 |
| Soil "Betokontakt" ("Knauf", Russia) | 28kg | 2.5 | 70. |
| Soil TiefGrung D14 (Dufa, Germany) | 51l | 2,1 | 107,1 |
| Washing "Old" (Optiroc) | 190kg | 0.5 | 95. |
| Shetrock Putclone (USA) | 84kg | 0.75 | 63. |
| Wallpaper Rasch (Germany) | 35 rolls | nineteen | 665. |
| Tile glue "Yunis" (Russia) | 260kg | 0.4. | 104. |
| Water-dispersion paint DUFA | 20l | 3,4. | 68. |
| Ceramic tile (Italy, Spain) | 33.4m2. | 24. | 801.6 |
| Metal entrance door Gardian (Russia) | 1 PC. | 905. | 905. |
| Lediva door blocks | 4 things. | 565. | 2260. |
| Total | 5459,1 |
Bathroom and toilet
Tied to a common riser (with water supply, sewerage and ventilation shaft pipes), a bathroom and a small toilet were very well located and turned out to be quite sufficient on the size, they were decided not to unite and not expand due to the corridor, as this is now fashionable. All efforts focused on the installation of new quality equipment, wall decoration, gender and ceiling, as well as selection of some accessories. The necessary communications to the locations of Santechpribors were already spent. Renting the house without finishing, builders set a simple cheap toilet and the same temporary washbasin, and even stretched the pipes where the bath should be. It remained only by laying out the floor and walls with tiles, install new equipment. The bathtop chopped, French, Jacob Delafone (18085cm), with legs and chrome handles ($ 620). For her, the Taron mixer (335241R) from GROHE (Germany) ($ 250) was chosen. Plus, they installed the sink from Falper (Italy) with a wooden (cherry, of course) tabletop, on holder and leg ($ 1166), with Taron mixer (331341R) also from Grohe ($ 173). On the wall strengthened the mirror with the Falper shelf and lamp ($ 548). From the mandatory little-stationary Soapon Florida from Grohe with the holder for $ 110 and the same glass of the glass with the holder twisted to the wall. Here, in the bathroom, the hostess put the wooden lattice box for the Calligaris linen (Italy) for $ 140 than the arrangement of this room and completed.For a small toilet, we bought and mounted a traditional "compact" with a horizontal release and a double tank button Giralda (Roca, Spain) for $ 265. In addition, for $ 82, a chrome-plated paper holder from GROHE (Florida series) has been purchased.
The cost of electrical work
| Type of work | number | Ral payment, $ | Cost, $ |
|---|---|---|---|
| Installation of wires | 280 M. | 3.9 | 1092. |
| Installation of electric hoists (sockets, switches, repaired boxes) | 84 pcs. | 10 | 840. |
| Installation of point, ceiling and wall light fixtures | 1 set. | 490. | 490. |
| Installation of electrical panel | 1 set. | 200. | 200. |
| Installation of floor heating system | 1 set. | 180. | 180. |
| Total | 2802. |
The cost of electrical materials
| Name | number | Price, $ | Cost, $ |
|---|---|---|---|
| Electrocabel and components | 280 M. | 0.9 | 252. |
| Electrical, Uzo, Automatic Machines (Germany) | 1 set. | 200. | 200. |
| Electric installation Simon | 84 pcs. | - | 956. |
| Celhit floor heating system | 1 set. | - | 729. |
| Total | 2137. |
Kitchen
Just as landscape designers do not advise to throw out the land when digging the foundation, the Alpine slides are made from it, the Master of the company "Gale" recommended not to demolish the partition between the living room and the kitchen. A small fragment of this wall (1,22m) was used as a constructive basis for mounting a part of the kitchen furniture of the Gala-floor cabinet and a bar counter stand. The result is a very comfortable, beautiful and unusual structure, complemented by bar chairs from Calligaris (4 pcs. At $ 333). Table top length- 240cm, Round radius- 40cm, and width, respectively, 80cm. The cabinet under the tabletop is divided into 3 parts: 60cm-large door, 90cm - Double swollen door, plus a retractable box, 60cm. In addition, in the depths of the rest of the kitchen furniture (colors of the cherry tree), the built-in technique is hidden.All kitchen furniture together with the built-in technology cost $ 4669 and was delivered 6 weeks after ordering, measurement and creating sketches and drawings. Asborka and installation were carried out in just 2 days. We will list the built-in furniture equipment: SERIE DELTA-INOX / GLASS extraction from Gata- $ 754, Hacking panel ENS 6690X from Electrolux (Sweden) - $ 550, oven 5696x oven from Electrolux- $ 758, 46A53 dishwasher from Bosch- $ 546 and washing machine 2065 (Bosch, Germany) - $ 511. Completes the composition of the kitchen high, height from the owner of the apartment, the refrigerator Liebherr (Germany) with a polished metal case- $ 1332.
Bedroom and dressing room
If the walls of the living room, hallway and the corridor are placed in monophonic wallpaper in the range of shades from sandy-gray to yellow-fawn, then in the most cozy room, the wallpaper of a pale olive tone with a slight greenish vegetable pattern was used. Medium-sized (14.7M2) The room is equipped as all others in the apartment, the minimum set of necessary furniture. It is in the bedroom exclusively domestic (Mekran, model "Stephenia line"), a beautiful shade of a cherry tree, which is well combined with the other wooden elements of the furnishings and decoration of the apartment. The kit made up such items: bed (under the mattress of 200 160cm) - $ 1448, two bedside tables - $ 300, toilet table- $ 403, bedside down - $ 196, mattress- $ 516, mirror- $ 164. Delivery and assembly of furniture were included in its value. For three rectangular lamps (Domus, Germany, the OGO-AN / S model) hanging on the walls on both sides of the bed and over the dressing table, paid $ 115.
The "filling" of a small wardrobe room is made by the specialists of the company "Furniture House Visconti" (Russia) for individual order with a preliminary measurement of the room and the creation of sketches. Delivery was made during the week, another week went to the assembly. The complex includes 11 positions, namely: boxes, matte chrome-plated handles, steel nickel-plated hangers, set of mounts for hangers, red wood colors, countersunk fasteners, power holders, eccentric tie, set of dowels and wanks. All elements of the assembly cost customers at $ 649, and the installation cost was $ 136.
Hall and living room
The concept of the furnishings and equipment of the apartment as a whole, formulated by the owner and the hostess, was as follows: "Nothing superfluous, only necessary, but good quality." This comfort formula is already felt in the hallway, in the same vein are equipped with other premises. All small furniture items for the hallway (from Calligaris) are made of Cherry wood: Stand for umbrellas CS-461- $ 178, Console table CS-477- $ 239, two mirrors in the frames: CS-487- $ 116 and CS-494 (7695cm) - $ 407, Hanger CS-497- $ 196 and CS-460- $ 199 newsmeal. But if here the listing of objects still takes several lines, then there are only white sofa in the living room, silver video bombard and transparent aquarium. Sofa "Manhattan 225a" ($ 1028) was produced by the Russian company "Factory March 8" and, in principle, can be collected from different modules, depending on the customer's desires. Filler cushion for seats and back-called latex foam polyurethane foam, covered first technical, and then upholstery under suede (Zamsha Fawn material). An impressive size, beautifully lit aquarium inevitably attracts the attention of guests to the mysterious and smooth life of fish and makes a serious competition in the neighboring TV, much less useful for tired eyes.Cost of sanitary work
| Type of work | number | Ral payment, $ | Cost, $ |
|---|---|---|---|
| Installation of water pipes | 19 pog. M. | 7. | 133. |
| Installation of sewage taps | 13 pog. M. | eight | 104. |
| Isolation of pipes insulation | 7 pose. M. | 2,2 | 15,4. |
| Installing a distribution manifold | 2 pcs. | eight | sixteen |
| Installation of toilet | 1 PC. | 45. | 45. |
| Installation of towel rail | 1 PC. | 23. | 23. |
| Installing the mixer | 2 pcs. | 19.8. | 39.6 |
| Bath installation | 1 PC. | 90. | 90. |
| Installation of washbasin | 1 PC. | 60. | 60. |
| Dismantling and installation of heating radiator | 3 pcs. | 130. | 390. |
| Total | 916. |
Cost of plumbing devices and materials
| Name | number | Price, $ | Cost, $ |
|---|---|---|---|
| Metal-polymer pipes | 19 pog. M. | 6. | 114. |
| Sewage pipe PVC | 13 pog. M. | five | 65. |
| Bath Jacob Delafone | 1 PC. | 620. | 620. |
| GROHE Mixer | 2 pcs. | - | 423. |
| Toilet Roca. | 1 PC. | 265. | 265. |
| Radiator heating fondital. | 3 pcs. | - | 308. |
| Total | 1795. |
Watch overpower