Repairs in a three-bedroom apartment with a total area of 82 m2 in the Moscow neighborhood North Chertanovo.
The hero of our story, a young and still unmarried man, was born and grew up in Moscow, in the area of North Chertanovo. His parents received new accommodation, and the former remains the son. So, the newly located owner of a three-bedroom apartment with a total area of almost 82m2 decides to make repairs. He is full of desire to equip everything in a new way and appeals to the specialists ...
A bit of history
The Moscow neighborhood North Chertanovo was built as the first in the city (and in the country) Olympic village. Near the ponds, a school with a beautiful pool, Bittsevsky Forest Park, an equestrian complex. Not the area, but a dream. It was in this village that the first two-tier apartments appeared, and on the last (receiving) floors under the workshops of artists, special premises with double light were given.The technology of staining walls (in the hallway, living room, pantry, in the kitchen) was as follows. First, the wallpaper glue was glued to the "Celli", then coated with acrylic primer into two layers with a sequential drying of each. Next, painted with domestic water-level paint, diluted with water by 10-15%. After drying, once again covered the same, but more thick white paint. The last coating was made by the paint Tikkurila, mounted on the "Monicor Nova" system. All these preliminary surveys pursued two goals, firstly, guarantee the absence of cracks and, secondly, to reduce expensive paint consumption mixed in the caloring machine. But on the beautiful wallpaper for the whole apartment, the owner did not regret the money, spending about $ 3,000. The walls were aligned with putty, but the fiberglass did not fall. The bedroom was decorated with natural silk textile wallpapers. On the walls in smoking, real rice paper went, as well as wallpaper with a drawing of bamboo stems. The ceiling in the living room is saved by vinyl wallpaper with the image of the clouds.
Raddled the hymns, the Olympic Bear flew away in a balloon, the athletes of the Olympiad-80 were driving, and the houses built on a special project were populated by Muscovites. Then they were considered very prestigious housing. However, now, when for more than two decades has passed, anyone, who had to be in the area, could notice how the elite houses were somewhere somewhere, and even somewhat dilated. However, not everything is so bad. The inner state of the buildings is still quite decent - twenty years not the term.
The young owner required a certain set of functional premises. This is a spacious combined bathroom, pantry for the economic and sports equipment, the Cabinet-smoking and dressing room in the bedroom. All these wishes, he expressed the specialists of the architectural and construction company "Investgradstroy". Alexander Zelenskaya architects and Galina Dmitrieva very thoroughly worked out the original version of the apartment design project, which was approved by the customer without fundamental changes. Nevertheless, in the course of the project implementation, the change was still introduced. Working in order was also produced by the study of details. Work on the reconstruction and decoration of the apartment was carried out in the period from July 15 to December 10. So the housewarmer came to the new year.
Redevelopment
Initially, they invited email workers to make the simplest dismantling work, demolished all the interior partitions and removed the old tired tie. After that, the masters of the company were connected, which removed the wiring, dismantled the plumbing devices, and also considered the old paint from the ceilings, and wallpaper from the walls. After dismantling interior partitions (they are not bearing; carrying walls, only around the perimeter of the apartment) It turned out quite spacious and free space representing a rectangle in terms of fairly harmonious proportions of the parties - 7.311,6m. The breakdown rushed only two groups of risers in the former "wet" zone (sewage, water supply and ventilation).
The number of rooms, their location remained basically the same, but the outlines changed significantly. This is not surprising, as the purpose of redevelopment was to find new, more convenient proportions for rooms - in full compliance with the wishes of the owner. The bedroom and the Cabinet-smoking were 13.68 and 8.09m2, respectively. The minimum reasonable bedroom area determined the presence of a wardrobe in it. If it were not for this absolutely necessary premises, the bedroom could have a smaller area.
Floor
After the delivery of outdoor convectors "Breeze" (KZTO, Russia), it was possible to start creating a screed in the entire apartment. This work required 11 days. Such a sequence of operations is explained by the fact that the convector must be built directly in the floor, and only the ventilation grille remains above. The height of the convectors together with the grille is 83mm. Before pouring the screed, metal boxes were previously installed on the slab (along the window in the living room), which later it was planned to build all convectors. The screed was made from the sandbetone "Birsss-7". The solution was laid on the latex coating waterproofing of FEIDAL (Germany). The consumption of waterproofing mixture was 1kg per 1.5-2m2 two-layer coating. When pouring a cement-sand tie, this waterproofing protected the slab overlap from leaks to neighbors from below, and in the future it will be insulated from the penetration of moisture from the bottom. Due to the high height of the built-in convectors, the thickness of the screed turns out to be considerable: 55mm in places flooring parquet, 73mm in places of laying tiles, 66mm in the bedroom, where carpeted coating will be laid on the phaneer. So managed to do without additional sound insulation. Consumption of sandbetone at the same time amounted to an average of 146 kg / m2. On the perimeter of the screed, in places of adjustment to the walls, the foamed polyethylene "Cellon" was laid with a thickness of 8mm to reduce the acoustic relationship of the screed and interior partitions.Parquet in the living room is laid on the traditional technological scheme "Crawling-plywood-parquet". Selected domestic parquet "Rainbow", Oak Select, dimensions of planks is 50070222mm. Total purchased 27m2 at a price of $ 45 / m2. The floor is covered by German varnish from Berger-Seidle, resistant to scratch. First, the Aqua Seal Economy Glossy lacquer lacquer was laid, from above, the same varnish, but already semi-wave.
Electrician
Igor Kuzmenko, based on the experience of implementing previous projects, was categorically against the bookmark of communications in the screed. In this case, with the future changes possible in the future (this may be the construction of new partitions, installing sliding doors IT.D.) The risk of damage to the wires. Therefore, the entire wiring was hidden in the suspended ceiling from GLC and in the newly erected partitions.
Cost of work on the device of floors
Type of work | Area, m2 | Ral payment, $ | Cost, $ |
---|---|---|---|
Refractory waterproofing of overlaps | 80.4. | 2.5 | 201. |
Cement-sand tie | 80.4. | nine | 723.6 |
Device of self-leveling tie | 9.7 | 2. | 19,4. |
Flooring plywood on glue with fastening on a dowel-nail | 25.9 | 3. | 77.7 |
Floor coating device (carpet) | 9.7 | five | 48.5 |
Flooring device (piece parquet) | 25.9 | 35. | 906.5 |
Flooring of floors with ceramic tiles | 44.8. | 12 | 537.6 |
Total | 2514,3. |
Cost of materials for flooring device
Name | number | Price, $ | Cost, $ |
---|---|---|---|
FEIDAL refinery mastic | 73.5kg | 4.9 | 360,2 |
Dry mixture "Birsss-7" (Experimental plant dry mixtures) | 11500kg | 0.05 | 575. |
Optirok bulk floors (Finland) | 55kg | 0.65 | 35.8. |
Plywood 12mm (Russia) | 25.9M2. | 4.8. | 124.3. |
Parquet piece, glue Tarbikol (France), Varnish Aqua Seal Economy (Berger-Seidle, Germany) | on 26m2 | 52,7 | 1370. |
Carpeted coating (Belgium) | 10m2 | fourteen | 140. |
Ceramic tile (Spain) | 41,8m2. | 28. | 1170.4 |
Adhesive Tile "Unice" (Russia) | 360kg | 0,2 | 72. |
Total | 3847.7 |
Convectors "Breeze-M" (KSTO) are mounted in rectangular gutters, recessed in a screed to a depth of 80mm. They go along the entire window on the right side of the apartment for six meters. Two convectors of 2,5m and 1m 1m were ordered. Each is a copper tube with aluminum plates attached to it, inserted into a long metal box without a lid. Instead, the last top lay the grille. Of the variety of proposed models, a rolled rolled, made of bright oak slats, rushed into two polyethylene strings. This grill is best combined with a light oak parquet. To remove dust, the lattice is folded.
The issue of managing the entire complex of lighting devices was agreed in advance between the customer and the author of the project. The owner's desire was such that he would have the opportunity to create the desired combination from these groups and could, leaving or returning to the apartment, include a ready-made light scheme by one-only press on the switch in the hallway. So it was done. First, through a plurality of different switches (the entire group of the togglers is mounted at the input door), the necessary combination is set for all illuminated zones, then using a single switch, which is immediately located, can be turned on and off the entire lighting scheme. It's comfortable. For example, do not be confused in the switches when you come home with a company of good friends and want to immediately get a bright, sensation of the holiday lighting. Or- to put the atmosphere of the poetic night, when a guest is a wonderful lady.
Two light sources will be stolen. The first is inside the wardrobe for sliding glass doors. Daylight lamps are built into the ceiling. In the evening, even with closed doors, their smooth radiance penetrates all corners of the interior. Daylight lamps are mounted and wide, almost in the entire wall, but a shallow (7cm) niche at the head of the bed. Rather, in the upper part of this niche. This second source allows you to create a local backlight over the pillows. But this light is quite enough to illuminate the weak, calmly the whole bedroom too. The owner decided that with these two sources of light there is no need for a central ceiling lamp.
Cost of work on the installation of partitions and suspended ceilings
Type of work | Area, m2 | Ral payment, $ | Cost, $ |
---|---|---|---|
Laying of walls of foam concrete blocks | 51.8. | 12 | 621.6 |
Installation of suspended ceilings from GLC | 34.8. | 22. | 765.6 |
Installation of suspended ceilings | eleven | 15.6. | 171.6 |
Installation of stretch ceilings | 13.7 | eight | 109.6 |
Total | 1668,4 |
Cost of materials for mounting partitions and suspended ceilings
Name | number | Price, $ | Cost, $ |
---|---|---|---|
Foam concrete unit 60030075mm, glue "Wins TM-17" (Russia) | 337 pcs. | 1,4. | 471.8 |
Stretch ceiling (Italy) | 13.7M2. | 32. | 438.4 |
Suspended system "Lumsvet" (Russia) | 1 set. | 250. | 250. |
Plasterboard sheet, profile, fasteners | 35.1 m2 | eleven | 386,1 |
Total | 1546,3 |
Walls and ceilings
The design of the house has an interesting feature: both longitudinal outer walls in which windows are not supporting. Window blocks are mounted in lightweight structures from a wooden bar, are insulated with mineral wool blocks and are covered with asbestos panels on both sides. This feature allowed to dismantle part of the outer wall from the side of the loggia and put a completely glazed partition with a profile from PVC. The living room and the kitchen area are now literally poured by daylight from a huge stained glass glazing in full width of the apartment. The remaining structures on the other wall (around the bedroom windows and the cabinet) were opened on the inside and re-insulated according to the following scheme: plastic film plus fiberglass wool ISOVER plus polyethylene film. Attack is covered with inside moisture-resistant plasterboard. Additionally, the locations of the framework of the frame and the outer sheaving were processed by the sealant "Stez A", and the external gaps between PVC-boxes of windows and the Sazilast 10 wall-sealant (both of the company "Sazi").
Partitions were erected from aerated concrete blocks 60030075mm. The selection of this material was determined by the characteristics of the blocks themselves, simplicity of treatment, good degree of sound insulation, and most importantly, the possibility of erection (under certain skills) of curvilinear surfaces. The partitions were deliberately delivered directly on the plates of the inter overlooking, after that, the screed was made. The partition plan, according to the project, was marked directly on the slab overlap, after which these walls were laid out by two installers in 12 days. Burned blocks cement glue for cellular concrete "Win TM-17". The main time in the construction of semicircular partitions in terms of partitions was gone on trimming segments, fitting and grappling masonry of curved planes.
All partitions were plastered by plaster plaster "Plastor" (Rosen's firm). The curvilinear surfaces were shuffled "under beacons" with the help of special patterns cut on the site from the plexiglass. The walls were finally aligned with Pufas putty (Germany) in three layers with intermediate grinding. For dry putty, smooth walls were caught with nonwoven fiberglass "web". Usually, on top, they put sand again, but in this case they were accepted differently. Fiberglass only primed and painted. The only minus of this technology is that, being a fibrous material, "Pautinka" absorbs a large amount of primer and paint.
The ceilings in the apartment are made by different technologies. The living room and in the kitchen is a moisture-resistant plasterboard, fed by metal frame. From it, in the living room zone, a caisson with luminescent illumination is made, but the vinyl wallpaper inside the caisson with the image of the clouds was laid on the plastered concrete surface. Stallement - seamless stretch ceiling (CERUTTI SOFFITI TESI, Italy) from the composite canvase. The chicken ceiling is plastered with plaster plaster and is saved by the same wallpaper as walls. The ceiling in the bathroom is made illuminated: the lumsiver mounting system for a conventional modular suspended ceiling is filled with "milk" plexigl, inside the daylight lamps are located inside.
Windows and doors
Two windows and a glass wall leaving the loggia (Proplex PVC profile and single-chamber double-glazed windows) were installed at the second stage immediately after the end of the dismantling work. The cost of the large (160180cm) windows in the bedroom- $ 368, the window in the Cabinet smoking less (160120cm) and cheaper. It cost $ 207. Asaya dear, of course, a huge glazed partition (270700cm) with a door between the living room and the loggia - $ 3960. It must be added to the total cost of installation of all these window structures- $ 845. After installing windows and marching the seams, they were closed with slopes with slopes, leveled and painted dufa semi-wave enamel (FullStoff Innen, Germany).The cost of making decorative elements
Type of work | number | Ral payment, $ | Cost, $ |
---|---|---|---|
Installation of columns with plasterboard niches | 2 pcs. | 98. | 196. |
Installation of a niche for home cinema | 2,3m2 | 22. | 50,6 |
Installation of the table in the bathroom | 1 PC. | 375. | 375. |
Total | 621.6 |
The cost of materials for the manufacture of decorative elements
Name | number | Price, $ | Cost, $ |
---|---|---|---|
Plasterboard sheet, profile, fasteners | 1 set. | 230. | 230. |
Total | 230. |
The cost of plastering, painting and facing works
Type of work | Area, m2 | Ral payment, $ | Cost, $ |
---|---|---|---|
High quality shuttering surfaces | 218. | 12 | 2616. |
Flooring surfaces with wallpaper (including in color) | 79.5 | nine | 715.5 |
High quality coloring of surfaces | 218. | 13 | 2834. |
Facing walls with ceramic tiles | 42,2 | nineteen | 801.8. |
Total | 6967,3 |
The cost of materials for the production of finishing works
Name | number | Price, $ | Cost, $ |
---|---|---|---|
Plaster Gypsum (Russia) | 2600kg | 0.25. | 650. |
Puff Pufas (Germany), wallpapers "Staters" (Russia) | 1 set. | 802. | 802. |
Tikkurila paint (Finland) | 68 L. | 6. | 408. |
Wallpaper vinyl | 12m2. | five | 60. |
Natural Silk Wallpapers (Japan) | 28m2 | 75. | 2100. |
Rice paper wallpapers (Japan) | 40m2. | 29. | 1160. |
Ceramic tile G.Versace (Italy) | 42,2m2 | 47. | 1983,4 |
Adhesive tile "Unice" | 380kg | 0,2 | 76. |
Total | 7239,4 |
Risers, pipes, radiators
Water supply rims pipes for reliability were replaced with new, they were embedded with gas welding. The joints of the cast-iron sewering risers were crying and replaced the old packing from the cleaved paneling polyurethane sealant, to eliminate all the possibility of penetrating unpleasant odors. The new sewasonal layout of polypropylene pipes (Valsir, Italy) was attached to cast-iron risers through rubber adapter cuffs. For the entire plumbing scheme used Italian ball valves of the company Bugatti. Having sufficient experience of reconstruction of apartments, the head of construction Igor Kuzmenko recommended not saving on the purchase of materials and components related to communications. It is dangerous and economically unreasonable to lay a miner delayed action under its own housing. The plumbing network was made of copper pipes in the KME polymer protective shell (Germany) "on the soldering" and on the collector scheme. That is, to each point (bathroom, shower, a toilet, sink) from the distribution cabinet stretched separate pipes of hot and cold water. The wiring of the sewage tubes was thought out so that they should not be dragged into the carrier reinforced concrete wall, but only in partitions. Napanese was installed faucences of production of Italy. The heated towel rail (since it is not intended for Russian networks) attached to the riser of hot water through the adapter manufactured by the company "Time" (the model of the West-A-500-H). It works on the principle of heat exchanger. Heats up from the DHW network and transmits heat to a small amount of water, which, in turn, circulates along the pipe of the imported towel rail. It turns out that it is heated with its own, independent contour. Even in the case of depressurization on the floor, no more than 10 liters of water. If we take into account the waterproofing of the floor in the bathroom, made by the Bitumen-rubber masty of the company "Knauf", this will not let you flood the apartments of the next floor below. Warmer Honeywell (USA), collectors - "Combs" (Viega, Germany) and a water heater of a cumulative type (ATLANTIC, France) for 50 liters are mounted.
The appearance of a glass wall in the living room area and kitchen demanded the restructuring of the entire heating scheme in this part of the apartment. Figh, as already mentioned, the outdoor convectors "Breeze M" were mounted, and the pipes of heat supply were decided to hide. There was a question how to do it. Here is a glass wall. Tamin-concrete carrier. The output was alone to close the pipe with light decorative designs. For this, they came up with a new detail, the so-called rams (hollow, non-carrying structures that simulate real columns). They are created very simple. Asbic cement pipe (the only environmentally obstructive material in the entire apartment) with a diameter of 400mm was cut vertically to four equal parts and was scratched with oil paint to eliminate the fall of harmful asbestos particles. Then, with the help of self-tapping screws, the rashlock was attached simultaneously to the wall and to the PVC design of the window. The small capitals of the columns (in doric style) are made of gypsum plaster. Their form "pulled out" using the curly rule on classical technology.
Bathroom
The bathroom was the owner especially the road. He wished her to see the most spacious as possible, but taking into account the equipment, which at the time of the start of repair was already purchased. At first they decided to install a shower cabin. But she would partially tanned the beautiful ceramic tile G.Versace, which on the project was decided to separate the walls. Therefore, an idea arose not to put a ready-made module, several not corresponding to the overall style, but to create an original shower cabin on the spot. The entire area of the floor was closed by bitumen-rubber mastic of the company "Knauf", poured the screed. Extinguishes the near corner of the bathroom, built from foam concrete two vertical walls of the cabin and raised the floor in this place. The height of the small podium was 15 cm, which is enough to drain the water. Mounted drain gear. The walls of the cabin, like all the walls in the bathroom, were processed by German waterproofing "Dichtungmastic" from Feidal. Later, the entire design was plastered with a gypsum mixture for wet and wet rooms from "Rushan" (Russia). We were covered with the composition of "Fugaphite" and stuck tiles. Podium, a table for a washbasin and a bath fence are unique. Their frames were also made on the spot using gas welding from the profile pipe of the rectangular section (3030mm, the thickness of the metal 2mm) and are covered with moisture-resistant plasterboard with a thickness of 12mm. Then the table and the podium were the same, in two layers, were processed by the Bitumen-rubber mastic of the company "Knauf", and then glued with tiles and borders. As the customer wanted, the tabletop, with the sink strengthened into it, it turned out a large: length - 1.50m, width - 0.6m.The cost of electrical work
Type of work | number | Ral payment, $ | Cost, $ |
---|---|---|---|
Installation of wires | 260 pose. M. | 1.5 | 390. |
Installation of electric hoists (sockets, switches, repaired boxes) | 37 pcs. | 10 | 370. |
Installation of point, ceiling and wall light fixtures | 43 pcs. | 11.8. | 507. |
Installation of electrical panel | 1 set. | 200. | 200. |
Installation of luminescent illumination | 27.8 m. | 10 | 278. |
Total | 1745. |
The cost of electrical materials
Name | number | Price, $ | Cost, $ |
---|---|---|---|
Electrocabel and components | 260 pose. M. | 2.5 | 650. |
Electrical, Uzo, Automatic Controllers ABV | 1 set. | 460. | 460. |
WHERAGEFORMATION ABB (Germany) | 38 pcs. | 10 | 380. |
Light (Russia) | 37 pcs. | eleven | 407. |
Singlemptom daylight lamp | 31 pcs. | 10 | 310. |
Total | 2207. |
Living room, kitchen
In the interior of the living room implemented an interesting project idea: columns and portal were decorated with pebbles. To do this, we bought ordinary sea pebbles (it took 200kg for the entire apartment at a price of $ 0.2 / kg) and laid on the adhesive "Yunis-Plus", which was used for laying all the ceramic tiles in the apartment. Here I had to tinker. The most difficult thing was not so much to put these pebbles, how much to bring them to a decent thing to wash and clean it. Inscribe pebbles was covered with a varnish for stone from Tikkurila.The idea of the home theater The owner of the apartment has been given at the very first stage of project development. Under TV architect took a special niche. The curvilinear wall was made of plasterboard on metal frame. The frame of the lower part of the niche, on which, in fact, is all the equipment, is an approximately the same design from the profile rectangular pipe, which was used to create a washbasin in the bathroom. Two layers of ten-minute plywood lay on the frame on top, and the sides were trimmed with plasterboard and painted. The design turned out with a large margin of strength.
Cost of sanitary work
Type of work | number | Ral payment, $ | Cost, $ |
---|---|---|---|
Installation of water pipes | 32 pog. M. | 7. | 224. |
Installation of sewage taps | 13 pog. M. | eight | 104. |
Installing a distribution manifold | 4 things. | eight | 32. |
Installation of toilet | 1 PC. | 40. | 40. |
Installation of towel rail | 1 PC. | 36. | 36. |
Installing the mixer | 2 pcs. | 12 | 24. |
Bath installation | 1 PC. | 120. | 120. |
Installation of washbasin | 1 PC. | fifty | fifty |
Installation of a water heater | 1 PC. | 60. | 60. |
Installing the radiator and convectors | 1 set. | 450. | 450. |
Total | 1140. |
Cost of plumbing materials and installation devices
Name | number | Price, $ | Cost, $ |
---|---|---|---|
Copper pipes | 32 pog. M. | eight | 256. |
Pipes sewer PVC | 13 pog. M. | five | 65. |
Mounting plumbing materials | 1 set. | 650. | 650. |
Sink, toilet, bath, boiler | 1 set. | 1100. | 1100. |
Total | 2071. |
Cabinet and bedroom
The bedroom is made deliberately simply based on the direct destination of the room. Only wardrobe drawn attention. From the side of the bedroom, it looks precisely as a wardrobe, but inside is a lot of space for the storage of outerwear, linen, suitcases and vacuum cleaners. Fasting, as in the Cabinet-smoking, installed blocks of split-systems from the company General (Malaysia), working both on heating and on the cooling of indoor air. Mode "Heat" - 2.5 kW, "cold" - 2.2 kW. Smoking finger in oriental style. This exotic flavor is reinforced and selected furniture. Here will be two "Chinese" cabinets, which are made of furniture shields covered with black composition Pinotex and loss of sandpaper to create the effect of "rare", the surface. Drive from the cabinets will be built into a computer console. Heating radiators, to roll-up with walls, rice paper and wallpaper with a drawing of bamboo, closes the grille from bamboo, saws along the trunks.
The editors warns that in accordance with the Housing Code of the Russian Federation, the coordination of the conducted reorganization and redevelopment is required.Artist: Elena Stephala
Artist: Ekaterina Kryzhanovskaya
Finishing work: Igor Degtyar
Architect: Alexander Zelenskaya
Architect: Galina Dmitrieva
Plumbing work: Rafail Yanbeckov
Watch overpower