Uncomfortable door in the interior partition. One of the outputs in this situation is to move the opening and install a new door frame in it.
It often happens that the door located in the angular part of the room prevents you from optimally use the area, for example, in a small kitchen. One of the outputs in this situation is to move the doorway and install a new box with a door.
The new opening will be noticeably broader, after all, it still needs to install a pre-painted door frame (73204cm). Of course, you first need to purchase the door block to prepare the opening of certain sizes. Now on sale there are a wide variety of or without or without doors, smooth or embossed, covered with white paint or transparent varnish. You can buy the door and in general without the door box.
In our case, the old wooden door frame will remain in the same place, since its vertical racks are closed in concrete and their removal can noticeably loosen the wall. In addition, the external rack will be used as a side support for the new door frame. Imbling the work of the work of the door trims were already removed.
In the event that the door has a metal box, it must be removed without fail, the cutting racks at the floor level and removing the remaining burrs.
If the wall is made of durable material (vibratetone, brick, etc.), use a cutting diamond disk. When working it is not recommended to get up on a stepladder or staircase, they can begin to vibrate into a resonance with a tool. This goal is better to make construction layouts. When drinking a doorway in a septum with a thickness of 7cm, made of plaster or other not very durable materials, use manual hacksaw.
Before work
In order to determine the strength of the material from which the partition is made, drill three or four holes in the center of that part of it, where you decide to make a new doorway. At the same time, use a special drill on concrete and switch the drill to a vibration mode or use a perforation nozzle to a regular drill. Then check the possibility of sawing partitions through the well-done holes and select a suitable tool-cutting wheel or hacksaw.
Close the doors of the neighboring rooms tightly, because when drinking the opening (especially with the help of the cutting circle), a lot of dust is formed. We recommend using a respirator and safety glasses when working with cutting circle, and also periodically clean the workplace with a vacuum cleaner.
| The former doorway strengthen the spacer bars to reduce the vibrations of the top of the box during sawing. Establish need to install several bars. |
| Note the place of the new opening with a reserve around the perimeter no more than 15mm. This will facilitate the installation of the door box and will allow it to securely secure. |
| In the top of the vertical side of the placed rectangle, drill several holes in order to insert the blade of the hacks in the resulting cavity. Sawing from top to bottom to the floor. To facilitate the process of extracting the separated partition, cut it horizontally into pieces of approximately 30cm. Lightly tapping a heavy hammer, push them from the kitchen. Of course, in the place where they fall, there should be no objects. |
| After the new opening is completely cut, the chisel remove the separate detached pieces of plaster or other material. |
| The lower part of the opening is treated and clean the chisel. Then, on each side, drill holes with a depth of 8-9 cm, in which you then install the racks of the new door box. |
| Outside to the outside of a new box in a checkerboard order at a distance of 12-15 cm depraint of rotten screws. This will allow you to securely secure the door frame. |
| Install the door frame so that the lower protrusions are in advance drilled holes. Make sure that the box stands exactly horizontally and vertically and secure the racks in this position. Small breaks can be eliminated by laying pieces of gypsum. Check if there is a gap between the door and the floor. Making sure the correct installation, lock the box along the perimeter with pieces of gypsum. |
| After the doorway is transferred, seal the seams on both sides of the partition with cement mortar or mounting foam first at the top, and then in the direction from top to bottom. Cross and leave to dry. |
| Getting Started with an old doorway with gypsum blocks only after a solution or foam fully solidifies. At the site of the old opening, install the gypsum blocks and close the seams. After drying, apply a primer made on a plaster basis. |
Final finish
Discontinue the renovated room according to your taste. For example, leave the door to smooth, and on the opening impose decorative platbands to make it more relief. If this option is not suitable, apply some decorative ornament on the door or use paintwork for finishing.