We tell how to launder an acrylic bath from a limescale, remove the yellowness and rust.
Acrylic is a polymer with a small amount of pores. Therefore, they talk about its dirt-binding properties. That is, contamination particles do not stick to the smooth surface. But this does not mean that plumbing does not need care. On the contrary, it should be careful and regular, otherwise the bowl will quickly lose the primordial appearance. We will figure it out than washing acrylic bath and how to care for her.
All about cleaning acrylic bath
Acrylate care rulesCleaning from lime
Cleaning yellow
Washing Rzavchina
Industrial preparations
Prohibited funds
Plumbing rules from acrylic
The main rule is regular cleaning. Ideally, the surface should be washed daily. Make it very simple. The container is rinsed with warm water. Wash a soft cloth or a sponge without an abrasive side in a soap solution, gently wipe acrylic. Wash off foam water, dry wipes and bottom wipe. It's all that is needed to preserve the appearance of plumbing. If you do it daily, no additional manipulations will be required.
List of simple rules
- Each new detergent is tested on a small low-rise area. It is used in accordance with the instructions, after which they check whether the traces remained on the coverage.
- Rust with acrylic surface is removed with great difficulty. So that such stains do not appear, shower and cranes should be fully working. After use, they are tightly closed.
- Acrylate is easily scratched and cleaned. In these areas, a difficult dirt is accumulated. Therefore, it is impossible to use hard brushes, scrapers, abrasives for cleaning.
- Chemical preparations, even considered allowed for plumbing of this type, is not recommended to apply too often. Optimally do it 1-2 times a month.
- It is advisable to regularly apply a special polyrolol made on the basis of wax. It increases the smoothness of the coating, gives it additional mise-cycle properties.
- After washing the bath be sure to wipe dry. This prevents the formation of an unpleasant plaque.
Than laundering an acrylic bath from a limescale
A set of simple preparations, which will be found in any kitchen or in the first-aid kit, will help effectively get rid of most contaminants. True, it is best to remove fresh spots. But they act less aggressively than household chemicals. We give several proven recipes.Table vinegar
Use a 9% vinegar solution, but 72% essence. Even in this form, the tool may be dangerous for acrylate coating. Therefore, it is added in small quantities. The bowl is filled with warm water. It adds 0.7-1 l of table vinegar, stirred and leave for a while. More often for the night, but not longer than 12 hours. Then the liquid is drained, the surface is rinsed and wipe dry. Lemon acid, soda or salt add to improve the effect.
Soda
Removes lime flashes, well whitens the surface, but is abrasive. Therefore, it is necessary to use it carefully. There are two ways. The bowl is gaining warm water, they dissolve a pack of soda in it. Leave liquid for an hour, drained, wipe the coating dry. This option is good if the problem is small. The launched raid is better to wash off soda cashis. The mixture is divorced by water to the consistency of thick sour cream, applied to problem areas, it is withstanding 20-25 minutes, washed off.Lemon acid
It is used similarly to vinegar, in a divided form. Sold in the form of powder, which is dissolved in water. To remove the flare, it will take 150-200 g of dry agent. Important moment: lemon crystals need to be completely dissolved. If they fall on the walls, can damage acrylate.
How to wash an acrylic bath from yellow plaque
An unpleasant yellow shade appears on the surface for several reasons: javale impurities in water, irregular care, etc. Credit with yellowness is better with the help of household chemicals, but folk remedies also help.Hydrogen peroxide and vinegar
From the table 9% of vinegar and peroxide prepare a mixture, connecting them in a 3: 1 proportion. The resulting liquid is poured into the sprayer, applied to the yellowed coating. If there is no sprayer, make it a regular sponge. After 15 minutes it is necessary to wash and wipe the acrylic coating.
Mustard and Soda
A good choice, if you do not know what to clean the acrylic bath at home, when there are no suitable factory compositions. The mustard powder is mixed with an equal amount of soda. The mixture is divorced to the state of the cashecture with warm water. It is superimposed on the yellow sections, it is withstanding half an hour-hour, after which it is washed off.Laundry soap
Universal detergent. The higher the percentage of fat content, the better it copes with mud. Soap rolls on a shallow grater, the resulting chips are divorced to the state of a homogeneous gel. Add 2-3 tbsp. Spoons of soda. The paste is applied with a sponge to the surface, it is withstanding for about an hour, washed off.
How to remove rust
Cleaning rusty drips and stains are difficult. Help the following products.Lemon juice
Freshly squeezed juice is applied to the stain, withstand no more than an hour, wash off. To enhance the effect to juice, finely fused salt. So that it turned out a thick paste. It is imposed on rust, but in no case is not working. Otherwise, gloss will be spoiled.
Summer alcohol and hydrogen peroxide
Enough aggressive substances, so their impact should be briefly. To clean fresh rust, 5-7 minutes is enough. The ingredients are mixed in equal proportions, are applied to problem areas. The maximum allowable exposure time is 10 minutes.
What household chemicals can be used
- "Cinderella". Emulsion cream, removes the flare and the old rust. Incoming silicone forms a protective coating.
- "Type-Profi". Professional preparation for use at home. Disinfects, removes the most stable pollution of all types.
- "Sanelit". Antibacterial gel-shaped agent based on active oxygen, relieving rust stains and lime deposits.
- "Acrylan." Spray for the removal of rust and solar plaque. For a short time, forms a protective repulsive mud layer.
- Mr. Chister. Removes soap divorces, lime deposits, rusty sweels, kills bacteria.
Bagi Acrylan bathrooms
It should be remembered that, before you brush with any new composition of acrylate, be sure to try the novelty on a small fragment of plumbing. Strict compliance with the manufacturer's instructions is also necessarily.
What can not be used
- Metal brushes, scrapers, rags and washcloths with abrasives, melamine sponge. The latter is a very subtle abrasive, an analogue of the finest sandpaper. That is why it with such ease copes with any pollution. Melamine scratches and spoil the gloss.
- Powder preparations with abrasives.
- Chlorine. Destroys the gloss, acrylic becomes dim.
- Acetone, any other organic solvents. They enter the chemical reaction with the polymer, destroy its structure.
- Formaldehyde. Act similar to solvents.
With caution, it is necessary to clean the bath with alkalis, alcohol or acids solutions. They are quite aggressive, with improper use can spoil the coating.
We dealt out than you can wash an acrylic bath, what means it is better not to use. Surfaces from acrylic capricious, do not tolerate the effects of aggressive chemistry. Therefore, you should not forget about the regular simplest caring, for which you will need only a soft cloth and soap solution. The use of a special polyroli will secure the result.