What to do if the toilet tank flows: 4 frequent problems and solutions

We deal with the problems that provoke to the toilet: breakdowns with a float mechanism, a seal, cracks in a tank. And we advise how to fix them.

The failure of plumbing equipment is very unpleasant. Its repair is associated with unplanned expenses and temporary inconveniences. In order not to lose a lot of money and time, it is important to notice the problem as early as possible and immediately solve it. Find out what to do if water flows into the toilet after washed or constantly in the toilet.

How to eliminate leak from a tank

Signs of leaking

Problems and solutions

- wear of the seal

- Problems with a float mechanism

- leakage after washing

- Cracks in a tank

Prevention

How to check the service of the tank

Normally, the process of washing passes so. When you click on the drain key or the button, the old models may have a lever on the chain, the drain valve opens. Water under pressure enters the bowl and cleans it. The flow of fluid is most often a volley, short-term. But sometimes it can be longer.

After reset, the valve closes automatically, less often after repeatedly pressing the button. In any case, after its closure, there should be no leakage in the cup. If this is not the case, you need to test the tank for health. We list features indicating possible problems.

Signs of leaking

• In a cup, lime deposits or rusty divorces appeared near the drain.
• Periodically appearing or even permanent murder.
• Weak and elongated in time washing. It does not look like a strong volley out.
• Located closer to the reservoir, the flutter wet wall. The moisture appears even when the plumbing is not used for a long time.
• Moisture on the tank and on the pipes.

Condensate droplets appearing on the equipment indicates that the cold liquid is constantly circulating in the pipeline. Whereas with a normally working hardware should not be. If such signs appear, the wizard is recommended to start cleaning the inside of the tank. Sometimes the cause becomes the dirt accumulated in it.

To do this, lock the shut-off valve, the container devoid and remove the reinforcement from it. Carefully cleaned or lime and lime contaminants, collect the device. If the problem remains, is looking for another solution.

• 

What to do if water constantly flows in the toilet

The design of the reinforcement of modern models differs from obsolete systems with a rock float of rubber. New devices are equipped with two nodes: drain and float. The key or button activates the drain, it is carried out with a drain mechanism. After emptying the capacity, water supply is launched. It is adjusted by the float system.

The design of the modules may vary depending on the models. With their features can be found in technical documentation or when analyzing equipment. In the event that the toilet tank flows, it will still have to disassemble it. It is important to remember that it can be done only with a closed shut-off tap on the eyeliner or on an incoming riser. The tank before it needs to empty.

Disassembly scheme is simple. First, the drain button is unscrewed, then the lid is removed. After that, it is easy to get parts. The elements of the nodes are made of plastics, fixed using bolts and plastic or rubber seals. Details of different manufacturers are often interchangeable, so the replacement of wear is easy. Previously need to measure the wear product or come to the store.

We will analyze the main reasons why the toilet tank flows and how to fix the problem.

1. Spicled the seal

This is a ring made of rubber or plastics. It is located on the water jet exit site. It is delayed by the precipitate, fragments of mineral sediments and other pollution. Therefore, the reasons for such a breakdown happens two: the item is or too polluted, or worn out. In the second case, it is sophisticated, either deformed. Whatever causes the water to flow constantly. You need to change or clean the seal. The procedure is carried out according to such a scheme.

1. Remove the capacitance cover. We dismantle the mechanism. To do this, turn the left module to half the turn before clicking.
2. We prepare the washing solution with any soft soap. Clean the details.
3. Carefully inspect the seal. If there are cracks or deformation, replace new.
4. We put the module into place.

• 

2. breakdown of the float mechanism

There may be two options here. The first is the loss of sealed floors. In this case, it does not rise to the surface with an increase in the volume of fluid in the container. It is immediately noticeable with visual inspection. When filling the tank, the overflow system works, water flows from the tank to the toilet without a break. The second option is a breakdown of the mechanism. In any case, the module is required. This is done so.

1. We carry out diagnostics. For this, not devastating the tank, remove the lid. Press the drain key. We look at how the float works.
2. We dismantle the tank. Overlapping the locking crane, activate the flush key. We unscrew the suitable hoses and stiletto-fasteners. Carefully remove the tank from the shelf stand. It is heavy enough, it can not be dropped.
3. Remove float. It needs to be carefully unscrewed and replaced new. We put the knot on the landing place, securely fix it with plastic fasteners.
4. We put the tank on the toilet shelf, fix it with mounting studs. Connect flexible eyeliner.
5. It remains to install the cover, open the shut-off valve and make a trial washing.

3. Short-term leakage after plum

Sometimes the tank flows, while it is filled with a new portion of water. The reason may be the skew of the drain module. This is noticeable immediately. The drain key begins to love, sometimes it simply falls into the shelter. In this case, you need to dismantle the lid, remove the node. Most likely, he moved a little from his landing place. It is necessary to put it correctly.

It happens that a water flow brings quite large particles of mineral sediment or solid contaminants. They fall under the ring of the seal and disturb its tightness. In an empty reservoir, the pressure on the valve is small and it passes the liquid. As soon as the tank is gaining complete, the pressure is enhanced and the trickle is finalized. Eliminate a malfunction can be careful cleaning parts.

It is possible that it was broken or was originally defective one of the components of the valve elements. Here only replacement will help. The node is dismantled. Wearing elements are replaced if it is possible. If not, a new module is bought. After repair or replacement, the mechanism is installed in the tank. A trial start of water is carried out.

4. Cracks on the tank

Sometimes the cause of the leakage lies in the violation of the integrity of the tank. We will analyze how to eliminate the leakage, if the drain blade of the toilet cracked and flows. It should be understood that it is possible to correct the problem only for a while. The best solution is the replacement of plumbing, and it will still have to do. As a temporary measure, you can carry out a small repair. Do it.

1. We dismantle the tank. To do this, empty it, remove the cover, take out the reinforcement. We unscrew the fastep and eyeliner, remove the container from the toilet shelf.
2. Well dried out the outer and inner surface of the tank.
3. Suitable sealant neatly close all cracks. We act strictly according to the manufacturer's instructions. We give the material to open.
4. We put the container in place, fix bolts. We connect the eyeliner, install the reinforcement.

It is not known how much the equipment will work after repair. Therefore, it is desirable to plan the replacement of plumbing in the near future.

• 

Troubleshooting Tips

To less often eliminate leaks in the toilet tank, you need prevention. Preventive measures are simple and will not take a long time. It is necessary to conduct them regularly. We provide a list of necessary actions.

• Installing the water wiring filter. It delays large particles of pollution that retains the equipment in good condition. After installation, the filter must be cleaned regularly. Periodicity depends on the quality of tap water.
• Regular cleaning of the reinforcement of the tank and its internal surfaces. It is settled by the Ilobodoby Mass, the pieces of scale, and the like. All this interferes with the normal operation of the device. The lower the quality of water, the more often the cleaning is performed.
• Inspection of fasteners, sealing elements and equipment joints. The appearance of moisture, even a small amount of it, indicates a violation of the tightness of the compounds. It is necessary to remove the flow while it is small. It will take tighten the mount or replace the gasket.

Alone to eliminate the tank malfunctions will be able to every master. It is not very difficult and does not require special devices and tools. We must do everything neatly, before work, be sure to overlap the water supply.

•