For the manufacture of this lamp, you will need only covered with a pot of the pot (or a beautiful bottle) da labeled paper from a folded paper.
Why don't you try to make the original lamp of a beautiful bottle, a flower vase or a glass-covered pot? For its manufacture, only a few electrical accessories and lampshade of paper will be required.
Before work
Based on the neck diameter, determine the method of fastening the rod for fixing the cartridge: to the brass lid closing the hole of the vase, or in the rubber stopper, blocking the neck of the bottle. If you skip the wire through the tube, then you do not have to make a hole in the bottom of the vase to bring meals to the luminaire.
You need
- Vase or other beautiful capacity for the base of the lamp, the incandescent lamp is no more than 60W and the cartridge for it, one or two metal tubes, with the help of which adjust the height of the extraction of the lampsier and fasten the cartridge, 1,5m the electric pipe, the plug, switch and transition plastic ring, The lamb frame is 12 cm, for example, in the ampir style, a sheet is rather dense and light from the inside of the paper with dimensions of 22110cm, satin tape.
- Screwdriver and knife of the electromonter or pliers for stripping the ends of the electroplating, passage, hole punch, knitting needles, ruler, scissors, pencil and glue.
| Close the neck of the glazed clay pot brass lid with a rod attached to it on a rod with a bracket on which a sliding flat focus is located. Pre-adjust the focus so that when installing it is in the widest part of the pot. Fully put forward the stop of the bracket, thereby fixing the cover in the neck. |
| After you secured the lid, screw the two metal tubes with a length of 10 and 3 cm. If they end up slightly higher than the lampshar, it will visually increase the height of the lamp. |
| To suspend the electrically closer to the cartridge, skip it through the hole in the metal tube. Pull the wire with a reserve, it will be more convenient to connect it with the cartridge. |
| Clean the end of the wire for the length of about 1cm and connect it to the cartridge. To do this, secure each conductor on the appropriate terminal. The bare part Close the insulation to avoid short circuit. |
| Cut the electrical wire at a distance of fifty centimeters from the pot. Divide and clean the ends of all four conductors, then connect them to the corresponding switch terminals. |
| Screwdriver pitch the plug, remove it from the protective casing and connect to the other end of the electric pipe to the stripped and twisted conductors. Put on the plug of the casing. |
| If for the lamp you have chosen a vase with a narrow neck, then instead of the lid, use the rubber plug of suitable diameter. When screwing up the tube, the plug will expand a little and will be securely fixed in the neck. |
| Rubber plugs are of a wide variety of diameters, so even to a bottle with such a narrow neck you can choose a cork. To screw the metal tube with a thread will be easier using a screwdriver. |
| Slightly sell a sheet of paper for lampshar on the lines located every 2 cm, using a knitted needle and a ruler. Fold the leaf of the harmonica, then with a template 2 cm with a 2cm width on one side of each side of the folder for the holes with a diameter of 5mm. One of them should be located 2cm from the edge, and the second one-in 1.5 cm from the first. Use holes with holes in the outlined places (they must be arranged symmetrically relative to each other). On the first and last folds of the holes are not needed. |
| By making two rows of holes, turn the paper with the withdrawal side up. Take up the lampshade scissors as it is shown in the photo so that later in the holes it was possible to insert the top ring of the frame. Perform this operation carefully to accidentally do not wear paper. |
| Putting a lamp to a flat surface, glue together two extreme folds so that one of them closes the edge of the paper. After drying the glue, do missing holes and skip the tape throughout the lampsure, starting from the side opposite to the glued place. |
| The transitional plastic ring with thread will allow you to correctly fix the lamp shade on the cartridge. Put and secure the frame, following it to be located strictly perpendicular to the vertical axis of the bottle. |
| Install the lampshade, inserting the top ring of the frame into the holes of the bottom row. Carefully assemble and straighten the folds using a decorative tape. Tape and make a beautiful bow from her ends. |
