Many of those who were engaged in repairs, at least once face the problem when the mounting foam accidentally hits the skin of the hands. The sealant in a matter of seconds sticks to the skin and, if it is not possible to remove it in time, then get rid of the composition it will be more difficult. This article provides useful recommendations and instructions that will help effectively cope with the task.
Once reading? Watch the video!
Polyurethane foam sealant is used when carrying out finishing, construction and repair work, for example, insulation of premises and close up of cracks. It is difficult to submit such works that cost without the use of this mixture. Working with a mixture, you need to follow safety and worn gloves. Unfortunately, not everyone complies with precautions, and the composition may accidentally get into the open areas of the skin of the hands. Below are the recommendations that will be prompt than to rain the mounting foam from the hands, as well as how to cope with the situation to be prepared in the future.How to rain the assembly foam with remedies
If the mixture got into the hands, then it must be removed as quickly as possible. Do not allow it to dry and turn into a solid mass. Without losing time, take a clean rag and try to carefully remove the composition from the skin surface. Any other materials are suitable: wet wipes, cotton disks, etc. Try not to smear the dirt. Remove the mass, shifting a rag or a napkin from the outdoor spot to the center. First remove the upper layers, then clean the remnants. Delete follows gently, short fast movements. Do not rub and press with all the power.
Use detergent
You can get rid of the sealant if you soak your hands in hot water. Prepare a basin or bucket and fill it with hot water. Fill the rinse or pour washing powder. Leave your arms for 10-15 minutes, based on the amount of residues of the composition. To complete the procedure, rinse your hands with warm water.
Removal with special cleaners
If for any reason remove the residues of the mass does not work, then chemical and natural substances used by professionals to remove dirt from surfaces will help. Next, we consider how to wash the mounting foam from the hands when the primary means did not cope with the cleaning of the composition. Each cleaner has its advantages and disadvantages. We describe them in detail in individual items.Aerosols
Often, manufacturers of sealants produce aerosols that help to clean any coating from pollution. Aerosols are used to clean the gun and universal in application: they perfectly cope, removing dirt from skin and any items.
The aerosol can be bought along with the sealant and then the question is than tipting the mounting foam from the hands, will disappear. It is preferable to buy a composition and aerosol of one manufacturer, then the cleaner will be the most effective. The aerosol is used quite simply: the substance is sprayed over a contaminated area, after which the contaminated place is erased with a wet cloth or washed off the water jet.
Liquid solvents
You can remove various mixtures with contaminated surfaces using liquid solvents: acetone, white spirit, gasoline and kerosene. Also help to remove varnish. Chemical mixtures easily cope with the dirt and help to remove the remnants that fell into the skin epithelium.
To erase the composition, it is necessary to apply the solvent onto the cotton disk and go through pollution. The process takes from 15 to 30 minutes, taking into account the fact that chemical solvents have an unpleasant smell and time is necessary for weathering.
Despite the efficiency of the method, it is worth it in mind that the listed chemicals are toxic to the epidermis and can cause irritation, so it is better to prefer alternative options. In addition, the process is sufficiently long and uncomfortable. In extreme cases, solvents should be resorted to solvents when other methods are not available, or they do not help to remove the mounting foam.
Dimexide drug
The medicine is sold in pharmacies. It is used to remove dirt from the surfaces, so it is efficiently used to remove the sealant. The main disadvantage of the drug: may have side effects and even cause an allergic reaction. Quickly absorbed into the skin fabrics.Folk remedies
Some craftsmen know how to get rid of pollution by folk methods: with the help of vegetable oil and salt. These ecological products are clean, do not cause side effects and irritation and help effectively laundering the mounting foam from the hands. Before erased with vegetable oil, it is required to warm it up to the optimum temperature, so as not to burn, and grasp the place of sealant.
Before removing the oil, you need to wait from 10 to 15 minutes, after which it was washed with warm water. But there is a faster reception: Sprinkle a little washing powder or cleaning agent, after which we will erase the rigid sponge or rag and thoroughly wash the water.
Salt acts as an abrasive that cleans the surface from pollution. Sprinkle a polluted salt, intensely rubbing into the skin. Having finished the procedure, rinse your hands thoroughly with soap.
Than laundering a dried assembly foam with hands
If, for one reason or another, it was not possible to remove the mixture on time, and it was hardened, it is possible to erase it only with the help of mechanical devices - abrasives, or wait a few days until the sealant disappears on its own. The methods listed above will not help. The dried material is too tightly sticking to the skin, and in this case neither cleaners nor solvents and any other means for cleaning surfaces will not cope. Therefore, if you do not want to wait a few days, it is possible to drop the frozen foam only mechanically. Even manufacturers write about it.
It is not recommended to scroll the dry residues of the substance with rigid objects, such as a spatula or scissors. This may cause irritation. In addition, you risk the infection.
Prepare abrasive material: a rigid brush, pumice or rigid paper covered by abrasive. To reduce the risk of skin damage, it should be previously treated and prepared. Apply fat cream on a polluted area. This will provide a smoother slip and reduce possible damage. Before this, you can additionally displeate it, but optionally. This will help speed up the process of removing the mounting foam. Lubricate the surface of the brush or pumice with soap and carefully rub the composition so as not to cause damage until it is finally removed.
The dried remnants of the material are removed and with the help of nails, if not at hand of other materials. The process looks identically. In addition, it is quite effective. When rubing the frozen mass with our own nails, you can feel what areas remained intact, and do the procedure much faster.
Conclusion
In conclusion, several important recommendations. After cleaning from the mounting foam and washing, it is recommended to use cosmetic preparations to disinfect body portion and avoid irritation. Moisturizing hand creams are suitable, disinfecting and anti-allergy agents, antibacterial soap.
Try to use only verified methods listed in this article. Some methods can lead to negative consequences for the skin. For example, some use acetic or citric acid that can cause strong irritation.
Choose a method that seems most suitable to be prepared in such situations and, at least, do not bring to drying the sealant, because it is more difficult to remove the frozen composition and much longer. Start working only in special dense rubber or silicone gloves that do not miss substances, And do not neglect the safety technique. It will save time and free from unnecessary.
